JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser.

Home
Shure FP33 Mixer

Rycote Windshield Kit

Rycote Windshield Kit

Neumann TLM 103 - Nickel

Neumann TLM 103 - Nickel

Shure FP33 Mixer

Be the first to review this product

Shure FP33 3-Channel Stereo Mixer

$55.00

In stock

SKU

Shure-FP33

Connectivity
Inputs	3 x Balanced XLR inputs
Output	2 x Balanced XLR outputs (1 x L/R)
Headphone Outputs	1 x 1/4" TRS stereo 1 x 3.5mm TRS stereo mini
ALT I/O	1 x 3.5 mm TRS stereo mini - Monitor In 1 x 3.5 mm TRS stereo mini - Tape Out
Link Input/Output	"MIX BUS" connection: 3-Pin mini-XLR connector

Performance
Input Impedance	Mic: 1kΩ internal; use with 19 to 600Ω source; -10 dBV clip level Line: 50kΩ internal; use with ≤ 10kΩ source; +36 dBV clip level Monitor: 10kΩ internal; use with ≤ 1kΩ source; +21 dBV clip level
Output Impedance	Mic: 1Ω internal; use with Low-Z source; -31 dBV clip level Line: 150Ω internal; use with 600Ω source; +18 dBm clip level Tape: 2.2kΩ internal; use with >10kΩ source; +3 dBV clip level Headphones: 300Ω internal; use with 8 to 200Ω source; +11 dBV clip level
Gain	Low-Z Mic Input: Line 78 dB, Mic 28 dB, Headphone 89 dB, Tape 66 dB Line: Line 28 dB, Mic -22 dB, Headphone 39 dB, Tape 16 dB Monitor: Headphone 11 dB
Frequency Response	20 to 20,000 Hz ± 2.0 dB (channel controls centered)
THD	0.25% THD @ +4dBm output, 50 to 20,000 Hz
Equivalent Input Noise	-127 dBV with 150Ω source, 20 to 20,000 Hz
Output Noise	Master level fully CCW: ≤ -100 dBV, 20 to 20,000 Hz Master level fully CW: ≤ -80 dBV, 20 to 20,000 Hz
Common Mode Rejection Ratio	65 dB @ 100 Hz, -20 dBV input
Polarity	Mic/Line to Mix Bus: inverting all other signal paths are non-inverting
Overload Protection	Shorted outputs, even for prolonged periods, cause no damage. Microphone inputs of up to 3 Vrms cause no damage. The Line and monitor inputs can withstand signals of up to 30 Vrms.
Output Clipping Level	≥ -18 dBm @ line output into 600Ω
Oscillators	Tone Oscillator: 1 kHz ±10% Slate Tone Oscillator: 400 Hz ±10%
Limiter	Threshold: adjustable; 0 dBm to +15 dBm Attack time: 1 mS Release time constant: selectable; 100 mS or 1 second Indicator: green when limiting by 1 dB or more
Microphone Power	12V Phantom through matched 680Ω 48V Phantom: through matched 6.8kΩ 12V T (A-B): through matched 180Ω

General
LED Indicators	Input Channel Bi-Color LEDs: Green: Signal presence; visual indication of mix level Red: 6 dB below clipping level Output Peak/Limiter Bi-Color LEDs: Green: Output being limited by 1 dB or more Red: Output peak threshold reached; factory set at +17 dBm; user adjustable from 0 to 17 dBm
VU Meter	VU Left/Right Channel Output Level Meters: 0 VU preset at +4 dBm output level
Operating Temperature	Operating: 0 to 60° C (32 to 140° F) Storage: -40 to 85° C (-40 to 185° F)
Power	Internal: two 9V alkaline batteries External: 12-30 VDC to DC In jack; non-polarized
Current Drain	Approximately 41 mA (idle) at 18V
Battery Life	8 hours minimum, typical
Dimensions (H x W x D)	2.26 x 7.24 x 6.33" (58 x 184 x 161 mm)
Weight	3.5 lb (1.6 kg)

Write Your Own Review